6 Steps to replacing the Sanyo PLC-XW300 projector lamp

Written by
  • Shelagh M.
  • 13 years ago
Sanyo PLC-XW300 Projector, Sanyo POA-LMP132 (service parts no 610 345 2456)

Sanyo PLC-XW300 Projector

STEP-BY-STEP INSTRUCTIONS FOR SANYO PLC-XW300 LAMP REPLACEMENT

When your Sanyo POA-LMP132 (service parts no 610 345 2456) projector lamp is nearing its end of life you’ll see the  Lamp Replace Indicator on the projector flash yellow. Sanyo PLC-XW300 Replace Lamp Icon, Sanyo POA-LMP132 (service parts no 610 345 2456)
The Replace Lamp icon will also appear on the projector screen.
The lifespan of your Sanyo POA-LMP132 (service parts no 610 345 2456) lamp will vary depending on how much the projector is used and if the filters are cleaned regularly.

Before installation:

Buy your Sanyo POA-LMP132 (service parts no 610 345 2456) from an authorized manufacturer and avoid the lower-priced knock-off lamps. These fake lamps are usually made with counterfeit parts that are inferior and can damage the sensitive mechanisms in your Sanyo PLC-XW300 projector. They may end up costing you more if they damage your projector since they also void your warranty. Buying from a legitimate source keeps your projector under warranty and gives you a solid guarantee that the lamp you are installing is suitable for your projector.

Sanyo_projector_bulb_replacementFor additional savings, you can replace only the POA-LMP132 bulb and keep the original lamp cage. Watch our video guide and learn how.

Replacing the POA-LMP132 Lamp Assembly

1. Safety steps:

  • Turn off the projector and unplug the AC cord.
  • Allow the Sanyo PLC-XW300 projector to cool to the touch. This can take between 45 to 60 minutes. Don’t open the projector when its still hot since these machines operate under high temperatures and you can burn yourself.

 
Sanyo PLC-XW300 Lamp Cover, Sanyo POA-LMP132 (service parts no 610 345 2456)2. Remove the lamp cover for the  Sanyo PLC-XW300it’s  located at the top of the projector towards the back. Locate the screw holding the lamp cover in place found on the side over top of the ventilation holes. Loosen the screw to remove the cover.
 
 
Sanyo PLC-XW300 Lamp Cage Replacement, Sanyo POA-LMP132 (service parts no 610 345 2456)3. Inside you’ll find the Sanyo POA-LMP132 (service parts no 610 345 2456) lamp cage. Loosen all three screws holding the lamp cage in place. Grab the handles on the lamp cage and gently lift the lamp out of its socket. Place to one side. Be sure to dispose of the lamp properly through a local recycling program.
4. Take the new Sanyo POA-LMP132 (service parts no 610 345 2456) lamp cage by the handle—avoid touching the lamp surface as oil from your fingers can cause black spots to appear when the projector is turned on. Gently maneuver the lamp into place. Don’t force the lamp as this may damage it.
5. Tighten all three screws on the Sanyo POA-LMP132 (service parts no 610 345 2456) Lamp Assembly. Make sure the screws have been tightened properly or the Sanyo PLC-XW300  projector will not turn on. Replace the Lamp Cover and tighten the screw.
6. Re-connect the power cord and turn on the Sanyo PLC-XW300. If the lamp does not turn on after the warm-up period, try re-installing the lamp. Reset the lamp hour using the Lamp Control mode found on the Setting menu.
NOTE: Your old Sanyo POA-LMP132 (service parts no 610 345 2456) lamp should be properly recycled. These lamps contain mercury and can’t be placed into common garbage.

RESETTING THE SANYO PLC-XW300 LAMP CONTROL MODE

Resetting the lamp replacement counter will ensure your projector correctly tracks the hours left in your newly installed Sanyo POA-LMP132 (service parts no 610 345 2456) lamp.

Sanyo PLC-XW300 Lamp Counter Screen, Sanyo POA-LMP132 (service parts no 610 345 2456)

  • Turn the Sanyo PLC-XW300 projector on.
  • Press the Menu option to display the On-Screen Menu.
  • Press Point left/right button(s) to move a red frame poster to Setting Menu icon.
  • Press the black arrow point button to move the red framed pointer to the Setting Menu Icon.
  • Press Point Down button to move the red frame pointer to Lamp counter reset.
  • Press the Select button.
  • Another confirmation dialog box appears, select YES.
  • The Lamp box will disappear and the Lamp Replace Dialog box appears.
  • Select YES to reset Lamp Replace Counter.

Sanyo PLC-XW300 Lamp Reset Screen 2, Sanyo POA-LMP132 (service parts no 610 345 2456)

  • There are two modes for Lamp life control. Mode 1 lets the lamp be turned on even after exceeding the recommended total hours of use. Mode 2 lets the lamp be turned on even after exceeding the recommended total hours BUT the projector turns off automatically after 3 minutes.
  • The Sanyo PLC-XW300 projector has a Lamp control that allows you to change the brightness of the screen and extend the life of your lamp. High Mode: Brighter than the Normal mode. It will shorten the lamp life using this mode. Normal Mode: Normal brightness. Eco Mode: Lowers the brightness and reduces the lamp power consumption thereby extending the lamp life.  NOTE: When you reset the Lamp Replace Counter the Lamp Replace indicator stops lighting.

Prolong the life of your new POA-LMP132 lamp

You can prolong the life of your newly installed Sanyo POA-LMP132 (service parts no 610 345 2456) lamp by:

  • regular cleaning the the air filter
  • allowing the Sanyo PLC-XW300 projector to stand for five minutes per turning the projector off.
  • wait at least five minutes before turning the Sanyo PLC-XW300 projector off.
  • don’t operate the projector continuously without letting it stand for at least one hour
  • turned off every 24 hours

Leave a Reply

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.

Shares