When you notice a yellow blinking light on the top of your Sanyo PLC-XU30/PLC-XU35 projector, it’s time to replace the Sanyo POA-LMP35 (service part no 610 293 2751) projector lamp. Follow our simple step-by-step instructions below for a quick and easy installation of your new projector lamp.
Why buy authentic
Be sure to purchase only Sanyo POA-LMP35 to protect your investment. While knock-off lamps can appear to be a bargain due to their cheaper prices, these counterfeit models can actually end up costing you more in the long run. Knock-offare manufactured with inferior parts that can damage the sensitive mechanisms in your PLC-XU30/PLC-XU35 projector.
Buying a genuine Sanyo POA-LMP35 gives you a lamp made to meet the specifications of your Sanyo PLC-XU30/PLC-XU35 projector while keeping your warranty intact.
Looking for a less expensive option? Are you technically adept? Watch our step-by-step video on replacing only the Sanyo POA-LMP35 (service part no 610 293 2751) bulb instead of the entire lamp housing.
Step-by-step instructions for replacing Sanyo POA-LMP35 (6102932751)
- Allow the PLC-XU30/PLC-XU35 projector to thoroughly cool before changing the lamp. Turn off the projector, unplug the AC cord and allow 45 to 60 minutes for the projector to cool. These projectors operate under high heat and there is a possibility of being burned, if the projector is not fully cooled before changing the Sanyo POA-LMP35 (service part no 610 293 2751) lamp.
- The lamp cover for the PLC-XU30/PLC-XU35 is at the bottom of the projector. Gently turn projector over and loosen the screw holding the cover in place. Place the cover to one side.
- Inside you’ll find the Sanyo POA-LMP35 (service part no 6102932751) lamp cage. Loosen both screws holding the lamp cage in place. Grab the lamp handle and gently lift the lamp out of its socket. Place to one side. Be sure to dispose of the used lamp through a local recycling program. Don’t throw this lamp into the regular garbage as it contains mercury.
- Taking the new Sanyo POA-LMP35 (service part no 610 293 2751) lamp assembly by the handle place it into the slot. Avoid touching the actual bulb as the oil from your fingers can burn a black spot on the lenses or you can accidentally break the bulb. Don’t force the lamp into place — it should slide into the slot easily.
- Once the lamp is in, tighten both screws on the Sanyo POA-LMP35 (service part no 610293 2751) lamp assembly. Make sure the screws have been tightened properly or the PLC-XU30/PLC-XU35 projector will not turn on.
- Replace the Lamp Cover and tighten the screw. Re-connect the power cord and turn on the PLC-XU30/PLC-XU35 projector. If the Sanyo POA-LMP33 lamp does not turn on after the warm-up period, try re-installing the lamp.
- Reset the Lamp Replace Counter by following the instructions below.
NOTE: Your old Sanyo POA-LMP35 (service part no 6102932751) lamp should be properly recycled. These lamps contain mercury and can’t be placed into common garbage.
Reset the Sanyo PLC-XU30/PLC-XU35 Lamp Replace Counter
The Lamp Replace Counter for the Sanyo PLC-XU30/PLC-XU35 will track the correct age of your newly installed lamp and trigger the Lamp Replace Indicator. Failure to reset the counter may result in the projector not tracking the end of life for the Sanyo POA-LMP35 (6102932751) and letting the projector inadvertently use the lamp past its normal life cycle. Your Sanyo PLC-XU30/PLC-XU35 may stop working suddenly if the Lamp Replace Counter has not been properly set.
- Press the MENU Button to display the MAIN MENU. Press the POINT LEFT/RIGHT button and scroll right to select SETTING.
- Press the SELECT button to display the SETTING DISPLAY menu.
- Press the POINT DOWN button (a red arrow will appear).
- Move the red arrow to the LAMP AGE and then press the SELECT button.
- The message “Lamp replace counter reset?” appears. Move the arrow down to YES and press the SELECT button.
- Move the arrow to QUIT and press the SELECT button.
3 tips for extending the life of the Sanyo POA-LMP35 projector lamp
Extend the life of your newly installed Sanyo POA-LMP35 (service part no 610 293 2751) by following these helpful tips:
- Wait at least five minutes before turning the Sanyo PLC-XU30/PLC-XU35 projector off.
- Don’t operate the projector continuously without letting it stand for at least one hour turned off every 24 hours.
- Cleaning the air filter regularly will also prolong the life of the Sanyo POA-LMP35 (service part no 6102932751) and prevent the PLC-XU30/PLC-XU35 projector from overheating.
